Menu openMenu Close
What are you looking for?

PTC - Circuit Protection

On this page

Introduction PTC-circuit protection

When it comes to Polymeric Positive Temperature Coefficient (PPTC) circuit protection, you now have a choice. If you need a reliable source, look to SCHURTER resettable overcurrent protectors.

SCHURTER’S PTC products are made from a conductive plastic formed into thin sheets, with electrodes attached to either side. The conductive plastic is manufactured from a nonconductive crystalline polymer and a highly conductive carbon black. The electrodes ensure even distribution of power through the device, and provide a surface for leads to be attached or for custom mounting.

The phenomenon that allows conductive plastic materials to be used for resettable overcurrent protection devices is that they exhibit a very large non-linear Positive Temperature Coefficient (PTC) effect when heated. PTC is a characteristic that many materials exhibit whereby resistance increases with temperature. What makes the SCHURTER PTC conductive plastic material unique is the magnitude of its resistance increase. At a specific transition temperature, the increase in resistance is so great that it is typically expressed on a log scale.

How SCHURTER resettable overcurrent protectors work

The conductive carbon black filler material in the PTC fuse device is dispersed in a polymer that has a crystalline structure. The crystalline structure densely packs the carbon particles into its crystalline boundary so they are close enough together to allow current to flow through the polymer insulator via these carbon “chains”.

When the conductive plastic material is at normal room temperature, there are numerous carbon chains forming conductive paths through the material.

Under fault conditions, excessive current flows through the PTC fuse device. I2R heating causes the conductive plastic material's temperature to rise. As this self heating continues, the material's temperature continues to rise until it exceeds its phase transformation temperature.

As the material passes through this phase transformation temperature, the densely packed crystalline polymer matrix changes to an amorphous structure. This phase change is accompanied by a small expansion. As the conductive particles move apart from each other, most of them no longer conduct current and the resistance of the device increases sharply.

The material will stay “hot", remaining in this high resistance state as long as the power is applied. The device will remain latched, providing continuous protection, until the fault is cleared and the power is removed. Reversing the phase transformation allows the carbon chains to re-form as the polymer re-crystallizes. The resistance quickly returns to its original value.

Product selection

To select the correct SCHURTER PTC circuit protection device, complete the information listed below for the application and then refer to the resettable overcurrent protector data sheets.

1. Determine the normal operating current:

 ______ amps


2. Determine the maximum circuit voltage

 (Vmax): ______ voltsmax


3. Determine the fault current (Imax):max

 ______ amps


4. Determine the operating temperature range:

 Minimum temperature: ______ °C

 Maximum temperature: ______ °C


5. Select a product family so that the maximum rating for Vmax and Imax is higher than the maximum circuit voltage and fault current in the application.maxmax

6. Using the Ihold vs. temperature table on the product family data sheet, select the SCHURTER PTC device at the maximum operating temperature with an Ihold greater than or equal to the normal operating current.holdhold

7. Verify that the selected device will trip under fault conditions by checking in the Itrip table that the fault current is greater than Itrip for the selected device, at the lowest operating temperature.triptrip

8. Order samples and test in application.


The benefits of SCHURTER resettable overcurrent protectors are being recognized by more and more design engineers and new applications are being discovered every day.

The use of polymeric fuses has been widely accepted in the following applications and industries:

• Personal computers

• Laptop computers

• Personal digital assistants

• Transformers

• Small and medium electric motor

• Audio equipment and speakers

• Test and measurement equipment

• Security and fire alarm systems

• Medical electronic

• Personal care products

• Point-of-sale equipment

• Industrial controls

• Automotive electronics and harness protection

• Marine electronic

• Battery-operated toys

• Telecom electronics

CloseYou will be transferred to the selected country page address. Therefore you will leave the SCHURTER main page.
If you would you like to visit your selected country page, please click on the button below:
If you would like to stay on the SCHURTER global website, please click on the button
Note: Your country preferences for the SCHURTER Global Website are now saved.